Pneumatic Cylinder
FV/FX series ISO15552 pneumatic cylinder
TBC/XBC Series Standard Cylinder
VBC/LBC series ISO15552 pneumatic cylinder
IA series ISO6432 mini pneumatic cylinder
RAL Series Mini Pneumatic Cylinder
RA Series Mini Pneumatic Cylinder
SJ Series Mini Pneumatic Cylinder
SM series mini pneumatic cylinder
EG Series Round Pneumatic Cylinder
SE series compact pneumatic cylinder
ELS Slide Cylinder
SQ series compact pneumatic cylinder
Directional Valve
ET307
SR Series Valve Island
RV series directional valve
RV seris NAMUR solenoid valve
V221/NM221 Series 2/2 Solenoid Valve
V221/VP321 Series 3/2 Solenoid Valve
V52/V53 Series directional solenoid valve
V32 Series 3/2 Way Solenoid Valve
VA52/VA53 Series Pneumatic Valve
VA32 Series Directional Pneumatic Valve
V Series Directional Solenoid Valve
L Series Hand Pull Valve
Fluid Solenoid Valve
ELP Solenoid Valve
SLP Series 2/2 Solenoid Valve(Normal Close)
ZS Series 2/2 Solenoid Valve(Normal Close)
SLG Series 2/2 Solenoid Valve(Normal Close)
VX2120 Series 2/2 Way Solenoid Valve
EMCJ Series Full Stainless Steel Angle Valve
EMCP Plastic Actuator Series Angle Valve
Connector+ Coil
Coil
ZSH Series 2/2 Solenoid Valve(Normal Open)
HUS Series 2/2 Solenoid Valve
2V 2/2 Solenoid Valve(N.C.)
Air Treatment Unit
Pneumatic Accessories
氣缸安裝使用注意事項
■ 必須使活塞桿軸心和負荷的移動方向一致
■ 不要將固定式氣缸與進行圓周運動的搖臂連接(LB固定)，此時應與擺動式氣缸連接(CA\CB\TC固定)
■ 避免活塞桿直接連接受垂直重力
■ 避免活塞桿受扭矩力
■ 防止后活動餃接離出力點過長會導致活塞桿受扭矩力
■ 長行程氣缸上應設置中間導向支撐
■ 考慮負荷的方向，采取適當的安裝
■ 氣缸調試時，其節流閥應從全閉狀態逐漸打開，從低速慢慢地將氣缸的驅動速度調整到所需要的速度。
■ 氣缸的運動能量不能靠氣缸自身完全吸收的時，應在外部增 設緩沖機構（如液壓緩沖器或設計緩沖回路）。
x
x
EAC3000 F.R.L Unit
EAC3010 F.R.L Unit
EA Air Preparation Unit
EAW F&R
EA FR.L Combnation
EAR Regulator
EAL Lubricator
EAF Filter
EAW3000 Filter Regulator
EAF3000 Filter
EAL3000 Lubricator
E Series Air Source Treatment Unit
Muffler
One Touch-in Fitting
Hand Valve
Stop Fitting/Check Valve
Italian Style Metal One Touch-in Fitting
USA Style Brass Fitting
Metal Fitting
SS One Touch Fitting
Air Gun
PU/PE & PUS/PES Tube
PA Tube/PU Cutter
TSB Flame Resistant Tubing